#VIDEOPROJECTEUR SANYO PRO XTRAX MULTIVERSE PROJECTOR TV#

The Sanyo PLC SE20 projector can be used with video recorders, DVD players, video cameras, satellite systems, TV games consoles and other video sources. However, you can lower the resolution on your computer to 800ењ†00 when designing and giving presentations if necessary. To do this lines are missed out which doesn't give as good an image as a projector designed for XGA. Sanyo is now part of the Panasonic Group and officially discontinued its production and sales of projectors in 2012. This projector can display a 1024x768 image but uses a method called compression to display the 1024x768 lines into a 800ењ†00 display area. The Sanyo PLC-XF45 was also marketed as the EIKI LC-XT3, and the Christie RoadRunner LX100. This projector is for use with computers that display an 800ењ†00 (SVGA) pixel image. The Sanyo PLC SE ANSI lumens, which is adequate for use for audiences up to 40 people and can display a clear image in most rooms with the lights on and the blinds/curtains open.

All Sanyo projectors are designed for indoor use and cannot be used in direct sunlight. The higher the number of ANSI lumens, the brighter the projector is. Projector brightness is measured in ANSI lumens. The brightness of a projector determines how large an image can be displayed on screen and therefore the audience size. Type Speaker(s) - integrated Sound Output Mode Mono Output Power / Channel 1 Watt Speaker(s) 1 x mixed channel Lens Aperture F/1.7-2.1 Keystone Correction Direction Horizontal, vertical Vertical Keystone Correction -40 / +40 Horizontal Keystone Correction -20 / +20 In other words, a job worth doing.Image Brightness 1500 ANSI lumens Image Contrast Ratio 400:1 Image Size 84 cm - 762 cm Projection Distance 1.3 m - 10 m Uniformity 85 % Resolution SVGA (800 x 600) Video Bandwidth 140 MHz Display Format 480,000 pixels (800 x 600) x 3 Max Sync Rate (V x H) 100 Hz x 100 kHz Bulb type UHP Bulb life cycle 6000 hour(s) The end result for me was a crisp, brighter image, with no discolouration. Lastly, reassemble using the reverse procedure. Also, donвЂ™t do this anywhere you care about dust going all over the place. You should wear eye protection while doing this, and if the projector is particularly dusty, consider a dust mask for your nose and mouth. Compressors arenвЂ™t cheap, but in my view are a sound investment.ДonвЂ™t be a hero.

You can use canned air for this, but I prefer using an electric air compressor since they are higher pressure, and I donвЂ™t have to worry about how much of the can IвЂ™m using up. Once youвЂ™ve cleaned out the rest of the unit, do one final blast around the optical assembly to remove any dust youвЂ™ve dislodged from elsewhere.Dust seems to get in everywhere in these things. Once those parts all seem clean, blast air into any and every crevice you can find inside the rest of the projector.Get the face of the lens too (underneath the tweezers in the photo).Concentrate on the optical filters indicated by the arrows in the last picture.My approach this time was to simply blast as much compressed air as I could into the gaps around the assembly until no more dust was being ejected. In ideal circumstances I would remove the optical assembly, but itвЂ™s very fiddly to remove on this projector. Once youвЂ™ve got to this point, itвЂ™s time to begin dusting. Move these ribbon cables out of the way, like so. It will still be attached at the front so donвЂ™t try to remove it. Remove this screw and unplug these connectors.Дisconnect the three ribbon cables by pulling these toggle gently outwards. Remove these screws, remove the air filters, then turn over and remove the top cover from back to front. Remove these two screws and CAREFULLY lift out the bulb. Remove this screw to open the bulb cavity.

#VIDEOPROJECTEUR SANYO PRO XTRAX MULTIVERSE PROJECTOR HOW TO#

The following photos are a guide to how to get this bugger apart: Proceed at your own risk, and do not come crying to me if you break your projector. Remember that this procedure is definitely not manufacturer-approved, so donвЂ™t screw it up and then try to claim on the warranty. My goal here was not to completely dismantle the projector, just to open it up far enough for easy access to the optical assembly, where dust ingress causes the most problem. IвЂ™d already tried cleaning dust out with compressed air via the side vents, but clearly it needed a more thorough job. I quickly found advice online that a вЂњblotchy uneven purple in the image is caused by dust contamination on the green LCDвЂќ. I wasnвЂ™t convinced the new bulb was to blame, so I went looking for another explanation.

I have a lot of these projectors, and after replacing a bulb on one of them recently, I found that the image was a bit blurry, and there was an uneven purple discolouration across the screen.

Videoprojecteur sanyo pro xtrax multiverse projector